NETALLY AIRCHECK G2 WRLS TESTER
Mfg # AIRCHECK-G2
CDW # 4146292
Know your gear
Enhance your purchase
NetAlly AirCheck G2 Wireless Tester - network tester is rated
4.60 out of
5 by
9.
Rated 5 out of
5 by
Edgar Menchaca from
Our tech analysts can troubleshoot wireless without needing an engineer to intervene, and data is extremely accurate
What is our primary use case?
Our use case for the AirCheck G2 is mostly for our remote sites. We support about a dozen sites where there are multiple floors and multiple areas covered by WiFi. These areas are supported by local analysts who will go onto the floor and use the AirMapper on the device to troubleshoot any wireless that has been brought to their attention.
How has it helped my organization?
This product has improved things over earlier troubleshooting in our organization simply by providing a utility that our tech analysts can use to troubleshoot wireless at their sites, without needing an engineer to intervene for every single instance. Being able to upload maps via the Link-Live portal automatically means we can review them with the tech analysts and go through the steps of remediating the issues that they've been discovering.
This utility has made our staff more productive—extremely. It has eliminated countless hours of travel time to outside facilities, time that we can use for other tasks.
The solution has also greatly reduced the amount of troubleshooting time by giving us a utility that the technicians onsite can readily use to identify wireless issues, instead of having to work with multiple means to get the same results.
What is most valuable?
Definitely, the AirMapper Site Survey on the AirCheck G2 is the most valuable feature. It is really nice to be able to upload the maps remotely to the website, and then have the analyst upload the results so we can review the data. We use AirMapper on a regular basis. It is probably the most used application on the device, to troubleshoot wireless while the tech analysts are on site and the engineers are not able to make the trip there.
The AirMapper is one of the easiest things I've ever actually dealt with for any kind of wireless troubleshooting. It is as easy as using any smartphone on a day-to-day basis.
The AirMapper survey data for obtaining information is easy to use and a lifesaver on multiple occasions. It is easy to set up, easy to use, easy to follow the instructions, and the uploading and reviewing of the data are extremely helpful.
We use the AirMapper Link-Live service to create heat maps. Once the survey has been performed, we upload all our results to Link-Live where we view the heat maps and go over the rough data of the survey performed at the locations. The ability to validate and visualize the information that's gathered by the AirMapper is extremely useful and it's extremely easy to read. It provides extremely easy data points to review and to gather information from.
The ease of use of the handheld AirMapper compared to software for, let's say, a laptop, is night and day. The handheld device is used pretty much like a smartphone. It is extremely user-friendly and ready to go right off the bat.
The AutoTest feature also comes in handy quite a bit to view the connection status of the SSID that the user is currently using. It also displays the interference at that site connection.
The completeness and accuracy for wireless troubleshooting would probably rank up at about 95 percent. From when the surveys are performed, to the time the results are uploaded, to what we discover, it has been found to be an extremely accurate tool. We have used it many times to identify either troublesome areas that are missing an access point or that are experiencing some kind of interference.
What needs improvement?
The biggest improvement would be an easier upload over wireless to Link-Live. Currently, the device has to be patched into the Ethernet. The wireless upload has been giving us some issues.
For how long have I used the solution?
I've been using the AirCheck G2 for about two years now.
What do I think about the stability of the solution?
The stability of the solution is high and up there with any other product that I've used. By far, it is the product that we will continue to use and invest more resources into to put it into the hands of our engineers and our technicians.
What do I think about the scalability of the solution?
Currently, we have about two dozen AirCheck G2 devices deployed in our environment. Most of the roles of the people using them are tech analysts at the particular sites, but we also have division network engineers that use the device for troubleshooting on the spot, and to instruct the analysts on the usage.
How are customer service and support?
The solution's technical support, when we reached out, was extremely helpful, extremely proficient, and quick to respond. I would rate it at about an eight or 8.5 out of 10.
How would you rate customer service and support?
Positive
Which solution did I use previously and why did I switch?
Before choosing AirCheck, our other option was to perform a site survey with an access point and a laptop at a site, every single time.
How was the initial setup?
The initial setup was extremely straightforward. They provided videos for each module and we found it extremely useful.
From out-of-the-box, deployment—overseeing the product, to ready-to-use—was roughly 15 to 20 minutes.
What about the implementation team?
We used a reseller for the deployment at our organization.
What was our ROI?
AirCheck has enabled us to remove multiple tools to retrieve the same information. Previously, tech analysts would have had to use either mobile phones, laptops, or a combination thereof to obtain wireless troubleshooting. As of now, a single AirCheck provides much more information that is detailed and uploaded to Link-Live, which makes it extremely helpful.
Replacing those other tools has saved us both time and money. We do not have to rely on multiple methods and multiple data points to achieve the same outcome.
What's my experience with pricing, setup cost, and licensing?
The overall pricing of the solution means it ultimately pays for itself. Once you get your hands on one of these G2s and perform even just a site survey, using the data points that you receive, it speaks for itself. It is an extreme game-changer, and a lifesaver every single time it's used.
As far as I know, there are no additional costs besides the licensing fee.
The overall cost of the solution, compared to the time saved—the number of man-hours devoted to other means of troubleshooting—is incomparable. The device itself will perform these tasks in minutes, compared to hours. And even looking over the data points and providing a reference point for those data points saves so much time. It saves time because of the heat maps, the detail of every single data point captured, and the reports you can automatically submit.
Which other solutions did I evaluate?
We have used iOS apps to perform troubleshooting. Comparing Aircheck to iOS mobile apps, the AirCheck provides a more detailed overview and a greater spectrum of data points to review after the fact.
What other advice do I have?
The advice I would give others looking into this product is to try it for yourself. If you are in constant need of performing troubleshooting for wireless at any point in time, especially for remote sites, or for yourself at a physical location, the product speaks for itself. It is one of those devices that, once you use it, you will not return to anything else.
The biggest lesson learned from using the solution is that I should have tried it sooner.
Disclaimer: PeerSpot contacted the reviewer to collect the review and to validate authenticity. The reviewer was referred by the vendor, but the review is not subject to editing or approval by the vendor.
Date published: 2022-10-27T00:00:00-04:00
Rated 5 out of
5 by
reviewer1910559 from
A quick informational tool that is easy to learn
What is our primary use case?
Working in this company for a year and counting. I received the task of being mostly responsible for an extensive > 250 id. wireless environment, where there were quite some existing issues. These are mostly related to an ongoing vendor migration going on from one vendor to another.
The Wireless network is both responsible for work-, medical-, client-, and public-related converage (access).
As medical devices are included in this, it's important to have a reliable connnection.
(I am using the latest version. I update it quite frequently.)
How has it helped my organization?
In a child-treatment area, quite some issues existed on medical monitoring systems, where they would frequently lose connectivity. As these resulted in alarms and an increased personnel workload, these had to be minimalized.
Quite a hard hard task to troubleshoot, especially without anaylizing tools.
While we could do some basic monitoring, AirCheck really helped me out. I could simulate the medical devices. I can connect to the device and do a full check of the area to troubleshoot what is happening. In this case, I noticed that we had some interference and overlapping channels. So, the device was immediately useful.
In a way AirCheck made a lot of children and caregivers quite happy. While I might not have resolved everything, I have reduced the problems considerably.
Where there were about three or four of those alarms daily. I was able to reduce it to once or twice a week.
As the appliances are quite limited in their wireless capabilities, a complete avoidance is mostly impossible here.
What is most valuable?
I use a lot of its functions.
The most used feature is the AutoTest. This provides quick verification and troubleshooting options. It also offers the possibility to go quite in-depth. It goes through everything with a profile that you can define. It creates a profile and connects to our network, then it tries to make an outside connection. It goes through all the steps, and you can dig in through all the steps. So, you can go into the first step of the authentication and connection. Then, in the second phase, you can see the neighboring access points, possible interference, and overlaps. In the end, you can see if your final connection was successful, e.g., a connection to Google. You can see the delays and time. The final step is that you can integrate a report automatically, uploading that through either one of your systems or a NetAlly online portal.
Overall, the complete appliance is quite easy to use. Even without going through a manual, you can figure it out quite fast. It is quick and easy. On the device, there is a help function that also relates to the navigation you are on. There are predefined profiles, so you can compare.
It is a very quick informational tool. If you go to an unknown location, and you don't know that location, you can immediately see which access points are there. So, if you have to replace one and don't know which one it is, AirCheck will tell you. If it is a known vendor, like Cisco Meraki or Ubiquiti, then it will show you that information.
AirCheck provides in-depth information for resolving connectivity and performance problems. You can do a full analysis on the web interface. You can also download reports into a spreadsheet. I couldn't imagine it being more in-depth.
What needs improvement?
I have used AirMapper twice, but it was mostly just to try it out with a test case. It works, but it is limited for gathering WiFi site survey data. For quick, small, and easy things, it is great and useful. However, it is not for a complete environment, which shouldn't be your main task with this appliance. For example, instead of relying on this tool to do a complete hospital, you should use a more specialized device, and they offer that too.
I would like them to modify the interface. The button to change profiles is fairly small. When you have interventions, it is not always possible to have a ballpoint pen or perfect precision touch with it, since sometimes you need to touch it quite a lot when your hands are very dirty. I would like a special pen that is compatible with that responsive screen. That would make it easier.
I have used a simulation of the phone apps software on my laptop, but it was more of a hassle.
The battery requires current charging in between longer usage as it'll not be able to last through a whole day of using it.
For how long have I used the solution?
I have been using it for six to seven months.
What do I think about the stability of the solution?
There are some glitches, but that is mostly with the unresponsiveness of the screen. However, that is only if you have gloves, dirty hands, or applied some moisturizing cream. Apart from that, there are no stability issues.
How are customer service and support?
In the beginning, I asked for the possibility to export to flash drives. They have since fixed that with software. Their support is very fast.
I would rate technical support as seven out of 10. In the beginning, there were some delays.
How would you rate customer service and support?
Neutral
Which solution did I use previously and why did I switch?
We replaced an old Fluke tool. It wasn’t a bad tool, but as it was outdated and new devices are considerable higher priced (and complicated?), they were not really in scope for our use case.
NetAlly gave me a comparison of three tools, depending on what would best suit me. I was impressed at first sight by the overall build quality of the device and all it accessories, including a decent charger, locator antenna, sturdy rubber casing, and nylon bag. (I can’t say this is “standard” though, but we bought a cable tester at a later time and that included such extras as well.)
How was the initial setup?
The initial setup for the product was straightforward. You can grab it out of the box and figure it out.
It took five minutes to get it up and running, excluding any software upgrades, but those aren't required. I did those later on. Those upgrades took me about an hour to create an account and change all the settings to my preferences. However, it depends on what your preferences are. If you want quick and easy preferences, then it comes out-of-the-box. You just turn it on.
To implement it, you connect with your laptop or cellphone to a public access point.
What was our ROI?
We have seen ROI. I have found lost access points, and an access point can be quite expensive.
AirCheck has made our networking staff more productive. I am able to remain at my desk for a much longer time. Whereas, in the beginning I was being called away by problems every day. Back then, I had four or five tickets assigned to me every day regarding wireless. Now, it is that same amount but in a month.
The solution has reduced troubleshooting time by a lot. You don't need to go into your installation plans, etc. If the office is a couple feet away, you can simply go there. Or, if it is remote, you can have someone with the appliance go there, boot it up (taking 10 seconds), and it then will tell you which access points are there. You can then do the reverse by going into your reports. This will give you an overview of whatever you have and you don't have to search for anything anymore.
What's my experience with pricing, setup cost, and licensing?
The product has a pretty good price.
If I oversaw all the budgets, I might even pay double for it. Not that I want that, then I couldn't get it approved. I hope they don't increase the price with their future models. However, it is worth its price.
It comes out-of-the-box, even with updates. There are no requirements. You only need an account for any software updates, but those are free and easy.
Which other solutions did I evaluate?
We also evaluated Fluke. AirCheck is more user-friendly as a tool.
What other advice do I have?
It can be seen as the perfect, all-in-one solution. I would recommend AirCheck. Based on my experience, we bought a second one for cable networks.
I use the product along with some colleagues who use it. It was very easy to train them. I just told them that I created a predefined profile, pressed AutoTest, and voila.
Now, AirCheck is mostly used if there is a problem case, which is about once a week.
I used AirMapper once, and it works, but it requires a bit more preparation prior to using it. It is not something where you would go onsite and immediately start doing. It is best to create a floor plan and have the settings a bit predefined prior to going somewhere. It requires some preparation, but that is always required, since you would want to know the area that you were going to. However, it is straightforward. It will ask you to create a simple floor plan and have a description for it. You can then select the size of the room and do a passive or active test.
The passive test will do a rather quick overview to see all the broadcasts. Whereas, the active test will be roaming and connecting to each access point, which is more in-depth but takes a longer time.
I would give it an eight out of 10.
Which deployment model are you using for this solution?
On-premises
Disclaimer: PeerSpot contacted the reviewer to collect the review and to validate authenticity. The reviewer was referred by the vendor, but the review is not subject to editing or approval by the vendor.
Date published: 2022-07-13T00:00:00-04:00
Rated 5 out of
5 by
Rene Ruiz from
AutoTest gives a snapshot of your environment within seconds
What is our primary use case?
We use AirCheck G2 in a hospital environment. We use across 30 hospitals and use it to troubleshoot our wireless network. It helps me troubleshoot as well as identifying coverage and interference issues that we encounter throughout our organization. Also, it could be related to SNR readings not being great. Whenever those issues arise, we take care of those issues.
How has it helped my organization?
We can identify issues faster so we can resolve the immediate issue on hand if it is related to coverage or interference. One of the things that is great to know is if there is an offending access point or a rogue access point, then we can identify that and see where it is located within the facility.
I consistently rely on the information that the unit provides. I feel it is accurate.
What is most valuable?
I like the product because it can right away give you a snapshot in time by doing a self AutoTest. I like the AutoTest because it does a snapshot of your environment within seconds.
What needs improvement?
If it was capable of downloading MIBs onto the device, then we could identify the manufacturer. Sometimes, when I am troubleshooting, there is a Mac address. For example, there is a rogue device and it just gives us a Mac address, which is fine. It gives us something, which is better than nothing. It would be nice if it was able to download a MIB where we could associate it with that Mac address and the manufacturer.
What do I think about the stability of the solution?
I like it. I haven't had any issues with it at all.
What do I think about the scalability of the solution?
Right now, it does what it is needed to do from a two, four, and five gigahertz perspective. I don't think it is capable of WiFi 6 at this moment, but it does what it needs to do.
Within our organization, there are three network engineers using it.
How are customer service and support?
I have never used the solution's technical support. I have always done everything on my own.
Which solution did I use previously and why did I switch?
I did use freeware that was available previously. It was okay for being free. AirCheck definitely replaced that. It was the first major tool that I had for working on wireless.
I had used LinkRunner G2 and liked the product. So, I wanted to go ahead and continue using the NetAlly G2 line. AirMapper works for me. I didn't really have anything to base it against another competitor. I just looked AirCheck G2 up online and read the reviews.
How was the initial setup?
The initial setup was pretty straightforward. I did configure it to use five gigahertz, but if there is an issue where we need to use two or four, then it is easy to set up the profiles.
I could use it right out of the box. We just charged it up and it gave us a snapshot of what is good and bad.
What about the implementation team?
I was able to do it on my own.
What was our ROI?
We have seen ROI. Prior to AirCheck, we would be guessing what the interference would be. We were using coverage as a point versus all the metrics that AirMapper provides. Now, we are able to identify if it is a coverage issue or inference issue. It does everything all in one shot.
It has made our networking staff more productive. We spend less time because the device helps us by identifying the issue and providing a solution for the customer. Prior to not having this device, we would have to guess when an issue arose. Now, we don't have to guess. This can easily save us hours per call.
It has easily reduced our troubleshooting time by 50%.
It is definitely worth it. It makes you and your engineers more efficient when trying to troubleshoot whatever the wireless issue is.
What's my experience with pricing, setup cost, and licensing?
I just bought it from Insight.
It is definitely well worth the price. It is approximately $2,500. It pays for itself since it eliminates troubleshooting costs and labor due to all the money you would spend kind of troubleshooting the device if you didn't have any of these tools with you.
There is additional cost to support the maintenance, which I feel is a little pricey, but it does provide you updates for the device, e.g., whenever they do an update.
What other advice do I have?
While I would like to increase usage, there are no plans to currently expand it due to budgets.
I would rate it as 10 out of 10. It is efficient for identifying issues in the air.
Disclaimer: PeerSpot contacted the reviewer to collect the review and to validate authenticity. The reviewer was referred by the vendor, but the review is not subject to editing or approval by the vendor.
Date published: 2022-07-19T00:00:00-04:00
Rated 5 out of
5 by
Ernie Rumfield from
AirMapper creates heat maps to help us visualize a network and check for correct layout
What is our primary use case?
We use it for multiple purposes, but it's primarily to test link speed, whether on a workstation or a switch. We also do a point-to-point from building to building and from point A to point B, which is a data center to data center check. It's fiber- and copper-based, so we can do multiple things with it. It's a good tool that gives us a lot of information.
How has it helped my organization?
It brings a lot to our organization. It helps us check for bit error rate loss, if someone has complained about a low wireless signal. We can prove to them that there's nothing wrong with it and usually it's an issue on their side. We can check the data port connections and that everything has been done correctly and we can make sure the layout is correct. There's just so much this device does that it's unbelievable sometimes. You don't realize what it can do until you start to play with it.
When it comes to resolving WiFi connectivity and performance problems, the information it gives us is excellent: complete and accurate. It provides the results we need and the ones we go by.
And the AirCheck helps quite a bit for our monitoring purposes. Our team is the smallest one in our organization, but we're also the busiest, and it saves us time. Our network is pretty resilient and pretty diverse and we don't have too many issues, but it helps out quite a bit. It saves us 10 to 15 hours a week. It has also reduced troubleshooting time, knocking it down by 15 to 20 minutes per job.
What is most valuable?
What I like about it is that it has a bigger touch screen now. The old LinkRunner was not a touch screen. It's a lot faster than the old one.
We can send the results to their Link-Live cloud and then find people to look at them. We can give the results to our clients or our contractors and they can look at whether it passes or fails. You can save it to both the cloud and the local machine. And, if you save it to the local machine, when you plug it in, as soon as there is an internet connection it automatically uploads to your account.
And the one-button AutoTest feature is an amazing tool. It works well. It tells you whether or not you have shorts in your network, your PoE+ is running low on voltage, and shows you your link speed.
We also have the AirMapper Site Survey feature to go along with that. We can upload things and check them. We can download from it and walk through a building to make sure all the WAPs are working correctly and to check the bit rate error. I like AirMapper because it makes things a one-suite deal so that everything is together. It makes it easier to upload, download, check, and test. It's also excellent for gathering WiFi site survey data. It's a good feature and we're really impressed with it.
Another function of the AirMapper is creating heat maps in Link-Live. It's great at helping us visualize a network. We use it to double-check that things have been laid out correctly by our contractor, and it provides excellent results. If we need to move something a few feet here or there, or add something, it helps out quite a bit. AirMapper is quite similar to site survey software products. It depends on what you're familiar with. We're very familiar with AirMapper and that's usually what we stick with. We like how it responds and it's easily uploaded into our monitoring tools.
In addition, the small form factor of the units is one of the big features.
What needs improvement?
The only thing that would be an improvement would be the ability to do MPO/MPT testing, which is another mode of fiber, along with more options on the SFP to do that testing. It requires a multiple link fiber test, it doesn't use just one or two strands. It depends on whether they're base-8, base-16, base-12, or base-14 MPO/MPTs.
For how long have I used the solution?
I have been using AirCheck G2 for between a year and a half to two years.
What do I think about the stability of the solution?
It's very reliable. We had their original product and it's still going strong. We'll continue to use it until they no longer service it. We're really happy with the reliability and durability of it.
What do I think about the scalability of the solution?
With the new formats that are coming out, it will likely be more scalable.
However, it's not ready for WiFi 6 unless they are going to do a software upgrade. They recommended a new unit to do WiFi 6, but I would be happy if they would just provide a software update for it.
We use the AirCheck pretty extensively, every three to four days out of a five-day work week. We plan on adding more. I've added new equipment every year, but it depends on our fiscal period. I try to keep my team on the latest equipment, so that they don't have issues.
How are customer service and support?
When I have had issues I have reached out to NetAlly and they have responded very quickly. They're very good. They usually have a quick solution and, if they don't, they keep you updated on what they're working on and they get back to you in a very timely manner.
They reach out to me every now and then, every time that we need an upgrade, or if they want to try to sell me an upgrade.
How would you rate customer service and support?
Positive
Which solution did I use previously and why did I switch?
We were using the LinkRunner, the original AirCheck, and the original EtherScope version from when NetAlly and Fluke were partners. We're pretty satisfied.
How was the initial setup?
It's very simple to start with. They send it to you, they give you the information, you put in the serial number, claim the unit to your account, and it automatically uploads it to your account. It keeps you posted on when it's time to do a software upgrade and when to renew your AllyCare.
What was our ROI?
We see ROI very quickly, within the first year.
The cost of the solution, versus its ability to save time or solve problems is excellent. It's a wonderful tool.
What's my experience with pricing, setup cost, and licensing?
Pricing is on par with the rest of the industry and the licensing is decent.
The licensing fees depend on what you want. There is the high maintenance and coverage, which covers everything including free software upgrades. And if something becomes broken, we call them and they'll send us a loaner while we send the broken one in. They'll work on it, check it for us, and re-certify it.
Which other solutions did I evaluate?
I've checked other vendors' products including the Corning, Expo, and AFL stuff. We have stayed with NetAlly because of the dependability, reliability, and the tech support and customer service. We're pretty brand-loyal. We stay with stuff we really like and that we're comfortable with.
What other advice do I have?
It's a good all-around tool for our purposes. I highly recommend it to all my contractors and everyone we deal with. It's a great tool and we haven't found any issues with it. Nothing is perfect, but along with Netally's EtherScope, it's probably the piece of test equipment that is closest. It does everything we need it to do and a lot more.
Disclaimer: PeerSpot contacted the reviewer to collect the review and to validate authenticity. The reviewer was referred by the vendor, but the review is not subject to editing or approval by the vendor.
Date published: 2022-08-01T00:00:00-04:00
Rated 5 out of
5 by
Korry Gold from
It's portable and useful for troubleshooting, but you need to buy a support contract to get necessary updates
What is our primary use case?
I primarily use AirCheck for wireless surveys or for tracking down a specific AP. I have used it personally for identifying rogue AP's. Very cool feature to prove to a wireless vendor, Grandstream, that they are running a rogue AP MAC from their unit.
How has it helped my organization?
AirCheck helps us diagnose WiFi problems with medical equipment. For instance, if we get a call about a mobile ultrasound unit with a weak WiFi signal, we can dispatch a tech to that facility who can use AirCheck to identify the nearest WiFi access point. We can filter AirCheck for that key and locate the nearest neighbor to determine when it should be picking up the WiFi.
We need to prove that we have a solid WiFi connection before we send the equipment to the vendor to check the unit. Usually, the vendor needs to upgrade the driver or set the roaming feature to a more aggressive mode on the unit.
One handheld device is better than carrying a cart with an AP and a laptop. It's handy to troubleshoot or perform a wireless survey with only one device. It does an excellent job.
It saves time! I've used AirCheck a handful of times, and it was useful, but It didn't point the finger at the actual issue. It did indeed help to identify the problem. Very useful tool to have in your arsenal.
What is most valuable?
AirCheck has a feature that lets you play a tone so you can track down a rogue AP based on the RF signal. That's a cool feature. It can also help you identify interference like microwave ovens or Bluetooth devices. I also like the ability to link it to your online account. It sends a report via email and saves it on the cloud.
The reporting is basic but useful. It lets you know that it was able to reach the DNS and get an IP address from the DHCP server. They did a cut-over and had to use the link for AirCheck. Every time they plugged it into the network, it would send the report. It's helpful when you need to locate a cable.
What needs improvement?
Since the product is still new to me, and I'm new to the company, I find it challenging to figure out. I'm trying it out at home, so I'm working in a smaller environment with only three access points. When I tested it out, I realized that when it's broadcasting an SSID, it also shows the BSSID, which is just another access point broadcasting a shared SSID.
It was hard to determine which AP was which because it only shows the MAC address. It'll also display the MAC address of the BSSID, so it looked like I had 12 APs in my house. If I have three access points and each is a dual-band with an SSID or BSSID for each radio, it comes out to about 12 APs.
That's one of the bugs fixed in the latest firmware update, but it's only available if you have a NetAlly support contract. I'm trying to push them to give us that firmware update because it is a bug that should be resolved whether you have NetAlly support. If they gave us the firmware updates, we could probably help NetAlly identify additional bugs and improve their product. It seems like it comes down to money because they want you to buy the NetAlly support.
For how long have I used the solution?
I started to use AirCheck G2 about six to eight months ago.
How are customer service and support?
I had a battery problem with the device. Once the battery meter dropped down to two bars, the unit would start rebooting. It was still under warranty, so I contacted NetAlly, and they shipped me a new battery. I let the product go until it ultimately died. They identified the issue pretty quickly after I told them what it was doing, and the new battery shipped fast.
Which solution did I use previously and why did I switch?
I haven't been in the division long enough to know. AirCheck was purchased about three months before I was hired. I don't know if it replaced anything other than maybe a laptop with AirMagnet or some other wireless survey software.
What's my experience with pricing, setup cost, and licensing?
To activate most of the features, you need a NetAlly support contract. When you buy this high-dollar product, you should have access to most of the features. I would think that the NetAlly support contract should cover support, hardware, and software.
If you find a feature you need, you have to call them and add it, but you should be able to use the product. You spend money on and invested in multiple devices and can't even use half of the features. They should negotiate with large enterprises who buy large numbers of units to provide NetAlly support for all of them at a nominal fee.
What other advice do I have?
I rate AirCheck G2 seven out of ten. If you need to use its full capabilities, you should get a NetAlly support contract or wait until the company provides firmware updates without one.
Disclaimer: PeerSpot contacted the reviewer to collect the review and to validate authenticity. The reviewer was referred by the vendor, but the review is not subject to editing or approval by the vendor.
Date published: 2022-07-14T00:00:00-04:00
Rated 5 out of
5 by
Kevin Portsteffen from
Gives me excellent situational awareness and troubleshooting in an easy to use, lightweight tool, with robust functionality
What is our primary use case?
AirCheck G2 is my number one pull-out tool when I enter new customer sites because it starts quicker than any notebook or device I own. I use it to get an overview of the wireless LAN infrastructure at a customer's location. I take out the tool and get an idea of what's happening before I even enter the site. I can see which SSIDs the customer has, how they are organized, which channels they use, plus a quick overview of what's occurring on the customer's side.
My other primary use is to get deeper insights when troubleshooting. When a customer has a problem with the wireless LAN, I use the solution to get a preliminary idea of the issue, whether it's related to the wireless network itself or something else, like the DHCP or DNS services. The solution lets me see what's going on and understand where the problem originates.
What is most valuable?
Wi-Fi is divided into bands: a 2.4 GHz band, a 5 GHz band, and most recently a 6 GHz band. These bands are divided into channels, and for a properly designed Wi-Fi setup, I need to use specific channels to avoid interference. AirCheck G2 gives me an overview of which channels are used by the access points or who delivers the Wi-Fi, which gives me a clear picture of what's going on.
When it comes to deploying access points, AirCheck G2 can check the internet. I can plug in a cable originating from the access point and check if it is receiving an IP address and if the access point is getting enough power. I can quickly check the basic installation on the customer's side to ensure that everything is correctly set up to accommodate an access point in the environment.
There's a feature which helps me create a heat map. The product comes with a cloud service called Link-Live, which allows me to import a building plan. I can walk around a building and tap my location on the display to conduct a frequency scan, and see what signals are received. The result is a heat map, where I can visualize where Wi-Fi signals are and aren't received throughout the entire building.
We used to work with different tools, but having this solution is an excellent opportunity because it's so compact and ready to go. We don't have to carry a notebook or tablet to run the software. It's a handy device.
There are two perspectives to consider; mine and the company's, as the solution is a privately owned device. It isn't adopted company-wide nor used by the entire networking team. Therefore, we have workflows based on other tools, specifically Ekahau, which is why I don't use AirCheck G2 as much as I would like. I would prefer AirCheck G2 for these workflows as it is a more lightweight tool, but that would be a company decision. On the first release, some view modes were missing, but NetAlly has greatly improved their product. There may be other solutions that deliver more information through a spectrum view, but for a Wi-Fi-focused tool, there's nothing I'm missing.
I'm happy with the ability to create heat maps in Link-Live's cloud service. All the necessary information is accessible in the cloud service, so anyone who uses the device is synced to Link-Live. On the other hand, a product designed to be easy to use is made more complex by German data security laws, which means we need to be careful where data is stored. This is not a fault with the product, as I love the ease of use with Link-Live. Receiving permission for data to be stored in US-based servers solves this issue.
I think the results are accurate and complete. They are in line with the analyses of other tools. So from my point of view, the results are pretty accurate.
I think it has saved time. I cannot speak for the whole company because I only give the solution to my colleagues when they need it, as I own it. It made me more productive, and I always carry it with me. It doesn't require another tool bag or a tablet like the Ekahau Sidekick. I can use AirCheck G2 to check that the cabling team have done a good job without consulting a tablet or my notebook. The process of checking if network outlets have been patched and if I'm receiving an IP address from the correct VLAN takes about three minutes with the solution, compared to 15 without it.
It is hard to say precisely how much time the solution saves during troubleshooting. Using AirCheck G2, I can quickly tell if there is an issue with the Wi-Fi or service near the network, such as the DNS or DHCP. This is the first troubleshooting phase, which takes just a few minutes. However, this doesn't mean the issue is necessarily resolved. I know where I have to look deeper in the network. Therefore, I wouldn't say the solution guarantees to resolve issues faster, but it definitely speeds up the initial stages of troubleshooting. I can get a good idea of an issue and where I need to do further analysis in three to five minutes.
What needs improvement?
The display size could be larger. On the one hand, I would like that, but on the other hand, it would make the tool larger and heavier.
A feature I would like to see is the ability to charge the device via a PoE outlet. Usually, I need to charge it at home. It would be good to leave the device plugged in and charging at a PoE source at the customer site after a quick look at the network when I have moved on to other tasks.
Another NetAlly product called LinkRunner enables me to spoof my MAC address and avoid different results in testing based on that. I know the focus of AirCheck G2 is Wi-Fi, but it would be a nice feature to see. As security requirements increase, we must authenticate ourselves to access networks, and sometimes we need to use the client's MAC address to access the network. This isn't a required feature as it's outside the scope of the solution, but it would be nice to see.
For how long have I used the solution?
I have been using this solution for five to six years.
What do I think about the stability of the solution?
I have not experienced any stability issues with the solution. I have heard about some battery problems but have not experienced them myself. I own two AirCheck G2s. One is five to six years old and still has a good battery life; the other is two years old with no issues. The stability and quality of the product are excellent from my point of view, including hardware and software.
What do I think about the scalability of the solution?
I haven't noticed any scaling issues in terms of performance. However, as 6 GHz Wi-Fi is becoming more widespread, the solution may lose some functionality, as it isn't compatible with 6 GHz. This is a potential scaling issue moving forwards, as the device will lose the ability to analyze the full spectrum of Wi-Fi frequencies. That's the only issue I can see as far as scalability is concerned.
Which solution did I use previously and why did I switch?
There is a smaller NetAlly product called LinkSprinter, but this tool has a different focus as it's only for cable testing and network checking. It tells me if there is enough power and if the access point receives an IP address. I don't use this tool as much since I got AirCheck G2, but as they have different uses, I would not say one replaced the other. AirCheck G2 does a lot more than LinkSprinter, though the latter is still a great tool in its area.
I previously used programs like MetaGeek or WindFi on my notebook during my workflow. I still have those installed, but I AirCheck G2 instead as it's quicker.
How was the initial setup?
When I got my first device, I had to install the software on a notebook to get some network profiles. This was fixed with Link-Live, which means I can use the device out-of-the-box, and if I want to install some network profiles or predefined settings, I just plug it into any network source where I can reach Link-Live's service to sync. There have been many improvements. NetAlly has done a great job making the initial setup of the solution easier.
Which other solutions did I evaluate?
I didn't evaluate other options before choosing this solution. I saw it and wanted to have it, and it took me about one and a half years until I could afford it. I didn't look around because this product had all the features I required.
I would love to try NetAlly's EtherScope nXG because it has even more functions, but considering the balance of features and price, I think AirCheck G2 is still the best fit.
What other advice do I have?
I would rate this solution a ten out of ten, I love it.
I pull out the device and start it, which takes approximately 30 seconds. On the main screen, I can perform a basic check which lets me know if the cabling and network are prepared for the access points. It's just a click of a button or a tap on the display. Checking which channels the access points use is almost as simple, as it is accessible right from the main menu. There is no searching through deep or extensive menus with this product. The major functions are quickly and easily accessible from the main menu.
When I first started using the solution, it took some time to adjust to the small display size. Panning in the map is easy, and I had to adapt this to my workflow. The other tools we use to do site or heat mapping tend to have bigger screens, like an iPad or notebook. Once you get used to AirCheck G2, it's straightforward to use, and because it's so small, it's also very light to carry around, which is highly practical.
I used phone apps. I use an iPhone both as a personal phone and a company phone, and these devices are relatively limited when it comes to troubleshooting apps. I used to have...
Disclaimer: PeerSpot contacted the reviewer to collect the review and to validate authenticity. The reviewer was referred by the vendor, but the review is not subject to editing or approval by the vendor.
Date published: 2022-07-14T00:00:00-04:00
Rated 5 out of
5 by
David-Prusynski from
A portable, rugged device that reduces resolution time and saves thousands of dollars
What is our primary use case?
I use it mainly for three things. For one, I use it for wired connection. I also use it for a couple of things on the wireless mode, and I use it a fair amount for the wireless locate function.
I'm using AirCheck G2. I know they just came out with G3, which I don't have. G3 has some new features that sound interesting.
How has it helped my organization?
It is a pretty useful tool for some situations. It is a handheld device. It reminds me of something a UPS or a FedEx driver would have. This device is in my bag, and whenever I have to go on-site, I always bring it because I never know if I'm going to run into a wired situation where I want to do a wired test, or I need VLAN or port information. So, I just bring it. I already used it this week for that. It is always there, and it is a really simple test to run. With the live link, I can get historical data on that or at least store it. I use it for that a lot.
It is useful for wireless packet captures. I used it for that this week, and I've solved one of the biggest issues we had with a vendor. I was using it to get the captures and eventually found the solution based on those captures. It is a pretty easy device to do wireless captures. In some of our wireless environments, for example, in our Aruba environment, we can do captures on the APs, but in some of our Cisco environments, they've somewhat taken that functionality away on our 3800 APs. This device is small and convenient. It doesn’t need external antennas, and I can take it to a spot, do wireless captures pretty much anywhere, and then use Wireshark for analysis.
It is helpful for finding an access point. We're doing an upgrade at a hospital. I work with a cabling vendor who says, "You said you have an AP here, but I can't find it." I can search based on a MAC address or an SSID, find that, and use the locate function. It'll give me a dial indicator and a beep indicator of where this device is. I routinely find access points that we can't physically see, for example, above the ceiling.
It is useful when you're having reports of poor wireless. In such a case, one of the things I'll do is I'll just set this on check SSIDs. For example, in our hospitals, we use very specific SSIDs. If I see one that's not ours, and I know that's not supposed to be there, I want to find that device, and I want to know what's going on with that device. Sometimes, it is a vendor device, or someone has put a hotspot on, but sometimes, it isn't supposed to be there. For example, in a hospital, it is very common to have waiting rooms, and there is a cable TV set up in these waiting rooms. Sometimes, the cable company just turns their wireless on by default. I go in there, and then we contact the cable company to turn their wireless off there because it is impacting us.
I bought one out of my own money. So, I found enough value to spend my own money on it. The guys on our team saw it, and they used to say, "Wow, what's that? What are you doing with that? We should have one of those." I convinced my boss to buy one for the team. Tomorrow, we're going to do a big wireless upgrade in the hospital, and I'm bringing my AirCheck G2. Very likely, we'll run into a situation where it would be an easy tool to use for quickly diagnosing or understanding what's going on.
Wireless planning was one of the things for which we used it a lot last summer. That may seem counterintuitive, but our healthcare system is going through a big wireless upgrade, moving from Cisco to Aruba. We're a rural healthcare system. In some cases, we have a clinic in a town of 1,500 people. I had interns take the G2 and go through the northern part of our state and visit our sites. They used AirCheck to verify wall density and signal degradation through walls. With that information, we could more accurately model those locations in the software we use for wireless planning. We were able to use 20% to 25% fewer access points because I had accurate wall information. We saw the benefit right away of sending our interns to test these remote sites. We could see that we don't need as many APs because we actually measured, and we were not guessing about the wall density. We did that at 15 sites and saved thousands and thousands of dollars. I don't use AirMapper at big sites, but small sites are where we could potentially use it. Its functionality is so easy to use. It allows a less experienced person to be more productive personally. Some of the guys who were doing this work were summer interns. They're not network engineers yet. This tool is easy to use.
Speed of resolution is another benefit, and with that comes customer satisfaction. At one of the hospitals, I work with our Biomed team. I took my AirCheck with me because they were moving some monitors around. They were not network savvy. I was able to just quickly plug the Aircheck into our emergency department network jacks and document everything and say, "We're going to reserve that port for this device, and that port for this other device." I could send them an email with all the documentation. They were all set. They could go and implement the solution. To a large degree, our emergency department personnel don't know what happened, but it all works. That's a big thing.
We were having some voice quality issues with some of our iPhones, and it seemed like the Android devices didn't see it. A lot of nurses use little handheld devices that have messengers. So, they have texting on there, and they have voice calls. They also can use it, for example, to scan medication and things like that. They were reporting some voice quality issues. I ended up using my AirCheck to resolve the issue. I was able to show the vendor that on their iPhones, they were not using the correct QoS markings. What was happening was that the QoS was being effectively lost once it left their iPhone. So, we're not giving QoS priority throughout our network. It was a huge issue for us because not only does it impact the nurses, it potentially also impacts patient care.
It makes the speed to resolution faster, and then our staff goes on to the next issue. It enhances our end-users' happiness because they want their problems fixed fast. When I had those guys go out to our small clinics, I didn't have to send a more qualified engineer to be doing this work because obviously, they need to be doing other more intensive network work. So, it frees up the time of our skilled people to do other stuff. It is difficult for me to quantify that from a productivity standpoint, except to say that I saw thousands and thousands of dollars of savings, and I had my engineers doing other things. From what we pay a network engineer to what you pay an intern, might be a $30 per hour delta. I can give this tool to a summer intern making 25 bucks an hour to have him do this work versus having to send a $50 per hour engineer to do the work.
It is hard to measure the reduction in troubleshooting time because I'm never without it. I just bring it, and it is with me all the time. If I go remote, it is packed in my remote box. It is not the only tool I'm using, but certainly, for some issues, it can cut down the troubleshooting time in half or less. For example, one of the tools I use is Ekahau Connect, When I need to use Ekahau, it takes me 10 minutes just to get that set up so I can start using it. After I hit the power button on my AirCheck, it is ready to go in 15 seconds. Depending on the issue, it is just much faster to find a solution.
What is most valuable?
It is portable. It is rugged. It comes with a nice case. It has been dropped, but it doesn't break. I don't have a cracked screen or anything like that. It has pretty good battery life.
The other nice thing about it, which I have to admit, is that it has USB ports. When I do packet captures, it is really easy to put them on a USB stick and then bring it into my notebook for Wireshark analysis. I don't have to use Bluetooth and try to connect. I find that convenient.
What needs improvement?
It would be nice if I could import an AP list with a MAC address. When it looks at access points, it should tell me the AP name instead of the MAC address. When you get a MAC address, you can eventually find out where you want to go. However, a lot of times, if I just have an AP name, I know that's in this area or that's over there. I would like that function because AirMagnet, which is the precursor of this, had that ability where you could basically import a list of APs and MAC addresses, and then it could display those instead of just a MAC address. That'd be a nice function. We should be able to put an AP to MAC address in Excel and export it as a CSV file and then import it. That'd be nice to have because I have that information for all my hospitals. The one I'm doing this weekend has got 550 access points. It is much easier for me to look at an AP name than to get a MAC address. Currently, I have to go to a different spreadsheet and try to find that MAC address. If I had the AP name, it would be like, "Okay. Yep. See it. Done."
They are doing spectrum analysis in G3, which I would love to have in G2. That's a nice tool to have, and from what I heard, that's the same price. I'd like to have that. The other function I would love to see is the ability to test fiber. I know the $10,000 version has the ability to test fiber, but I would love this lower-cost device to be able to test fiber.
For how long have I used the solution?
I've been using this solution on and off for close to three years. I used it at a previous company. I also have my own personal one, and when I switched jobs and got into the current company I work for now, I showed it to them, and then we bought two.
What do I think about the stability of the solution?
--...
Disclaimer: PeerSpot contacted the reviewer to collect the review and to validate authenticity. The reviewer was referred by the vendor, but the review is not subject to editing or approval by the vendor.
Date published: 2022-08-30T00:00:00-04:00
Rated 5 out of
5 by
reviewer1884177 from
Gathers the data that we need, and helps in solving problems remotely and centralizing our troubleshooting team
What is our primary use case?
We are using G2, which is the generation two solution. It hasn't changed since we got it. Other than a few software updates, it hasn't really changed.
We use it to collect data for our Wi-Fi systems. We collect the data, and we push it up to Link-Live, and then we pull the data down and review it for any remote problems or troubleshooting assistance. We have a number of these units. We've got close to eight or nine of them that are out in the field. They're basically used by our technician staff to do that data collection for us.
We also have one for engineering so that we can take it on trips to get a better real-time view of the wireless system activity in an area.
When we do the real-time items, we're just using the data as a real-time tool. When we use Link-Live, it is going to the Link-Live Cloud, which can be called NetAlly's private cloud. It is within an account that we have visibility into. So, it is like a hosted private cloud. It is not publicly available.
How has it helped my organization?
We have a multiple office situation in our company where we have very geographically dispersed offices. It has allowed us to centralize some of our troubleshooting people because we can collect data remotely and more efficiently.
It allows our remote site personnel to collect data if they have a problem. They can then push it up. It goes up to the Link-Live portal, and we can then have visibility into it. We can look at the data with their portal, or we can download it to our computer, which is what I like to do, and then use AirMagnet to open and review the data. It allows us to do remote troubleshooting. It allows us to do remote Site Survey assistance, and in real-time, it helps us to do interference detection and find out who's running what in a certain area.
When we're collecting the data, we're using the AirMapper Site Survey feature. It is pretty easy to use. It is pretty straightforward. I can talk to a technician who is out in the field. I have a one-page write-up that they just follow. When they do it one or two times, it is pretty easy. It is fairly intuitive.
AirMapper Site Survey gathers the data I need. It does everything I need it for. I'd rate it a ten out of ten in terms of the ability to gather Wi-Fi site survey data.
We use phone apps a lot. We have a few different ones that we use, but phone apps only give you limited information, and because they are apps, our security posture is different on them. They give us some basic information, but they do not give as much detail as compared to what we get out of AirCheck.
What is most valuable?
The ability to push data to Link-Live is really important. On the main screen, you can see all the system parameters, and then you can also go and see all the current systems that are operating. They all have different SSIDs or system identifiers, and you can see all SSIDs that are operating in a certain area. Being able to see that and being able to dive into each one and figure out what frequency it is operating under is valuable.
It is a cloud-based service. I like the fact that our remote site personnel can push things to the cloud, and I can pull them down. Before all these cloud services, things were not as convenient. I like the convenience of being able to do that for the way I'm using this tool.
What needs improvement?
We use these out in the field, and because they're not allowed on our network, we usually have to have the person take them home and provide backhaul to them. In other words, they are not allowed through our firewalls to dump the data. So, we have to have them go to a separate wired network to dump the data. There could be an option to put an LTE and have a phone engine in it so that you can buy a SIM card for it and have it use cellular to download the data. That is something that would be nice to have. That's a little kink in this system right now. Other than using the Ethernet port to download data, it'd be nice if we could use either LTE or some other way to get the data that was collected by AirCheck G2 to our Link-Live portal. That's because our corporate network will not allow them to pass the data through. We do have a special place we can tell them to go and get it, but it is just that when they're out remotely in the field, they typically have to take it home and do it from their home computer.
My biggest complaint about it is that I wish it was cheaper. It would be nice if its cost was less because we would like to buy a few more. We're an international company. We have some in the US, and some in certain other countries that we could export to. There are a few other countries where we need to go through export control to send them, which is a problem. If they want to scale their product globally, it would be nicer if they have all the import-export items worked out or have good resellers in each country because there are certain places where we cannot buy the unit. They don't sell it there, and it is not allowed for importation because of its approval. That's why we haven't deployed it in some of these other places, and we're going through alternatives for importation.
For how long have I used the solution?
We first got an AirCheck back in 2018. It was the first set we bought. So, that'd be four years.
What do I think about the stability of the solution?
We have never had an issue with it. It is very stable.
What do I think about the scalability of the solution?
It is a hardware solution, which means you physically have to have a device. It is on par with other hardware solutions. It is not a software solution. That's why I wish it was a little less expensive because then I could buy more of them. If its cost was less, it would be more convenient. Because it is a hardware solution, it is okay, but it is not as scalable as we'd like. By design, it is only going to be about so good. So, we accept it.
I have bought ten of them, and nine of them are in use. One is for our lab, and the other eight are out in the field. Our engineers and technicians use it.
How are customer service and support?
For this device, I've had to call only once or twice. I didn't have any problem with support. We have an enterprise support account with NetAlly. So, we have a number. Their support has been really good. We haven't had a lot of need for it, but we have them under support.
I would rate them a nine out of ten. In the old days, they published a lot of phone numbers globally, which was really convenient. Now, I have to dig out the information if I'm out of the area or out of the country. I do travel internationally, and sometimes, I try to go online and get somebody, and then I try to call them. That's why I wouldn't give them a ten.
How would you rate customer service and support?
Positive
How was the initial setup?
It was straightforward. I set up a bunch of units, and it didn't take me long for the first one, and then the rest were really a snap. It was pretty easy.
What about the implementation team?
We don't buy it directly from them. We bought it through a reseller. We use a company called Anixter. They're great. They're always good.
In terms of deploying it, we did it internally ourselves. We have a managed contractor who works for us. He helps in deploying it for us, but it is not like a separate company where I put them in a box and mail them to him, and he fixes them. His desk is near my desk, and I just say that here they are, and let's get these put online. He mails them out to the people in the field who work for us.
What was our ROI?
Within a year, they justify their expense if you're using them efficiently. We have had two of them since 2018, and we've seen a return on investment with those. We bought some in December, and then we bought some in March. That's the other eight for this new global deployment. We are starting to see a return. By the end of this year, we could justify the entire cost.
It does save time for the people who need to use it. It does help us solve problems faster because we deploy it in places where we don't have somebody who can do the work. If we didn't have the AirCheck G2 units, we would have to send somebody out to these sites who had the right toolset, or we would have to mail a unit to somebody who was less experienced with it, and they would have to use it. By buying these units, we're proactive and ready for issues, and we're able to solve them quicker. Because we're able to solve them quicker, it creates a better return on our investment.
We also use AirMagnet, which is software. You put it on your PC, and you can run it with Wi-Fi adapters. It basically puts a similar analytics engine onto your laptop, and that's what I use. I don't use G2s as much because when I have a Cadillac, why would I want to drive a Chevy. That costs more money than AirCheck. These other ones are good and convenient in certain cases. Because we don't provide our field people with a company PC, we can't give them our licensed software. This is a lower-cost way of giving them similar functionality and having them help out in the field.
What's my experience with pricing, setup cost, and licensing?
It costs $3,000. It would be nice if its cost was less. I could then buy more. Currently, when we buy one, we make sure that where we need it is big enough, or if it is too small, when a person has a job, they have to get a temporary one mailed to them to use, which becomes a littl...
Disclaimer: PeerSpot contacted the reviewer to collect the review and to validate authenticity. The reviewer was referred by the vendor, but the review is not subject to editing or approval by the vendor.
Date published: 2022-06-27T00:00:00-04:00
Rated 5 out of
5 by
Mario Alessi from
Performs real-time spectrum analysis and is stable
What is our primary use case?
I use AirCheck to track down rogue devices connecting to my access point.
What is most valuable?
The airCheck is the real-time spectrum analyzer to see clients that could be connecting to our network, not just rogue networks out there, but rogue clients and other interference in that particular spectrum.
What needs improvement?
The solution doesn't have much functional information online. Most of the information online is regurgitated from marketing brochures. I purchased the solution for a job and sold it afterward because it is expensive.
The AirCheck is no longer available and its software is not updated for current use. Additionally, it is not compatible with Macintosh and must be run on an emulator to access the outdated Windows software. Since Fluke sold all its intellectual property to NetAlly, there is no longer any support for the original Fluke AirCheck, which further influenced the decision to discontinue it. Going forward, I would attempt to buy the newer NetAlly product.
For how long have I used the solution?
I have been using the solution for a couple of months.
What do I think about the stability of the solution?
The solution is stable.
What's my experience with pricing, setup cost, and licensing?
The upfront cost of the solution is around $4,000. This cost does not include service contracts for support.
What other advice do I have?
I give the solution a ten out of ten.
New users should consider purchasing the latest edition. The outdated models lack the latest Wi-Fi band, rendering them a poor investment. I made the mistake of buying an outdated version on eBay for $500, which I only used for a single project. I eventually had to resell it since it was incompatible with the new Wi-Fi band that emerged in the past five years. Hence, it is advisable to invest in the new version.
Disclaimer: I am a real user, and this review is based on my own experience and opinions.
Date published: 2023-01-29T00:00:00-05:00