Black Box Net-Ping Network IP Tester - network tester
Mfg # TS670A-R2
CDW # 379807
Know your gear
A properly functioning network should be music to your ears. Tune into your network with our Net-Ping Network IP Tester. Use this handheld tester to install and maintain networks running TCP/IP protocol.
With the Net-Ping Network IP Tester, you can verify physical layer connectivity between any two points on a network. The tester sends a data packet, or PING, to another IP address on the network and then receives the packet again. Set up two testers to PING each other and test network end-to-end operation before installing workstations, servers, or other network devices.
Run the tester on 10/100BASE-T Ethernet networks. It’s smartly designed to communicate directly with 10BASE-T hubs, switches, routers, NICs, and other equipment. It can also communicate with 10/100BASE-T equipment set for 10BASE-T. It identifies 100BASE-T equipment.
With the powerful PING function in this tester, you can run a wide variety of diagnostic tests to check the health of your network.
Features:
Now provides full 10/100BASE-T PING capabilities. Will PING any 10BASE-T or 100BASE-T equipment or a 10/100 auto negotiating switch.
Gigabit Link Signal Detection will decode 10BASE-T, 100BASE-T, 10/100BASE-T, and 1000BASE-T or Gigabit signals.
A profile storage capability enables you to prestore the parameters for eight locations for later recall at that site.
Use on Ethernet networks running TCP/IP protocols.
Designed to communicate directly with 10/100BASE-T equipment.
Verifies connectivity and operation in remote locations over the internet.
Enables you to test networks before installing PC's, servers, and other network equipment
Locates and identifies default gateway and subnets
Displays router and MAC addresses
Identifies hub and switch ports connected to specific outlets
Tests up to eight stored IP addreses individually or successively.
Warns when duplicate IP addresses are found
Verifies DHCP server function and IP addresses
Identifies wire-pair connections with reversed polarity
Ideal for troubleshooting, moves/adds/changes, network management, and remote office support.
With the Net-Ping Network IP Tester, you can verify physical layer connectivity between any two points on a network. The tester sends a data packet, or PING, to another IP address on the network and then receives the packet again. Set up two testers to PING each other and test network end-to-end operation before installing workstations, servers, or other network devices.
Run the tester on 10/100BASE-T Ethernet networks. It’s smartly designed to communicate directly with 10BASE-T hubs, switches, routers, NICs, and other equipment. It can also communicate with 10/100BASE-T equipment set for 10BASE-T. It identifies 100BASE-T equipment.
With the powerful PING function in this tester, you can run a wide variety of diagnostic tests to check the health of your network.
Features:
Now provides full 10/100BASE-T PING capabilities. Will PING any 10BASE-T or 100BASE-T equipment or a 10/100 auto negotiating switch.
Gigabit Link Signal Detection will decode 10BASE-T, 100BASE-T, 10/100BASE-T, and 1000BASE-T or Gigabit signals.
A profile storage capability enables you to prestore the parameters for eight locations for later recall at that site.
Use on Ethernet networks running TCP/IP protocols.
Designed to communicate directly with 10/100BASE-T equipment.
Verifies connectivity and operation in remote locations over the internet.
Enables you to test networks before installing PC's, servers, and other network equipment
Locates and identifies default gateway and subnets
Displays router and MAC addresses
Identifies hub and switch ports connected to specific outlets
Tests up to eight stored IP addreses individually or successively.
Warns when duplicate IP addresses are found
Verifies DHCP server function and IP addresses
Identifies wire-pair connections with reversed polarity
Ideal for troubleshooting, moves/adds/changes, network management, and remote office support.